Neu

XRAY X1'19 GRAPHITE LOWER SUSPENSION ARM 2.5MM - 372117

XRAY X1'19 ALU REAR BULKHEAD - MOTOR (RIGHT) - 373015

XRAY X1'19 ALU REAR BULKHEAD - LEFT - 373025

XRAY X1'19 GRAPHITE REAR WING MOUNT 2.5MM - 373036

XRAY X1'19 GRAPHITE TOP DECK 2.5MM - 376232

XRAY X1'19 ALU SERVO MOUNT - ORANGE - 376260-O

CNC-machined gear box height adjustment plate made from premium-grade graphite material. Increases performance in high-traction conditions, allows super-low ride height. To keep the drive shafts linear, the gear box can be raised by 2mm using optional graphite plates. There are two different ride height adjustable plates which raise either only the gear box, or the entire rear suspension.

Must be used with #324013 Alu Front-Mid Motor (3 Gears) Plate - Lowered -2mm - 7075 T6.

Short 2-Pad Slipper Clutch Set - Shocks in Front

• Allows frontward shock absorber mounting position
• Super narrow
• Externally adjustable
• Quick & easy tuning
• Ultra-efficient
• Lightweight
• Increases stability
• Higher cornering speed
• Better landings

Redesigned slipper clutch set allows the rear shock absorbers to be mounted frontwards. Frontward mounting position increases stability on surfaces where the rear of the car collapses, particularly in high-speed corners. Team drivers also prefer this position on low-grip tracks.

Power from the motor is transferred to the drivetrain via an externally-adjustable central slipper clutch for quick & easy tuning. The 2-pad slipper clutch ensures super-smooth clutch operation and efficient, consistent braking. It is very easy to make ultra-fine adjustments to the slipper clutch externally.

The slipper clutch pads are made from ultra-efficient SLS material with very-high slip efficiency, thus allowing very precise slip adjustment.

The lightweight slipper plates are machined from premium Swiss 7075 T6, additionally hardened before a final black surface treatment.

The plates have a machined relief which decreases the friction surface to assist with clutch slip adjustment. With this plate design, pressure is focused on the circumference of the clutch pads for increased efficiency.

Set includes 2-pad spur gears:

• #365775 Composite Slipper Clutch Spur Gear 75T/48P
• #365778 Composite Slipper Clutch Spur Gear 78T/48P

Black-coated, Swiss 7075 T6 aluminum front-mid motor plate lowered by 2mm. Holds the slipper clutch assembly and gear box. Allows super-low ride height, and increases performance in high-traction conditions.

Black-coated, Swiss 7075 T6 aluminum front-mid motor plate lowered by 4mm. Holds the slipper clutch assembly and gear box. Allows super-low ride height, and increases performance in high-traction conditions. 

Must be used with #321268 Graphite Gear Box Height Adjustment Plate and #321269 Graphite Gear Box Height Adjustment Plate (or #321270 XT2 Graphite Gear Box Height Adjustment Plate).

Mon-Tech WR4 Rally Body - 017-005

RIDE 10 Spoke Nylon Wheel White - 123

RIDE 24mm Pre Cut Slick type with LT inner Set of 4 pcs - 24025

Mon-Tech WR1 Body - 015-001

PROTOform F1 Rear Wing (White) for 1:10 Formula 1 - 1723-04

PROTOform is proud to release our first wing set for 1:10 Formula 1 cars, one of the fastest growing segments of on-road RC racing.

There were three main ingredients the team at PROTOform took into consideration when designing these wings: 1) look awesome, 2) be durable and 3) perform excellently on the track.

Starting with the aesthetics, the wings come with a sleek matte finish in your choice of white or black colors. Inspired by real F1 wing styling, this wing will give your 1:10 Formula 1 car an unmistakable look on the track. The rear wing is a true multi-element design featuring slots in the side dams, just like the 1:1 cars. The middle element features an emblazoned PF icon. Rear downforce can be tuned by removing either of the upper elements, creating a “Monza-style” setup for high speed tracks. There are also three different mounting positions on the plate to adjust the height of the wing if your chassis does not have this feature. This wing set will fit most popular F1 cars on the market such as Xray, Tamiya, Yokomo and Roche.

PROTOform V2 F1 Front Wing (White) for 1:10 Formula 1 - 1729-04

Introducing our next-generation front wing for your 1:10 F1 car, designed for versatility, drivability and unmistakable style.

The V2 F1 Front Wing features 3-way adjustability to suit any condition your track throws at you: a low-downforce option, a medium downforce with 1-element add-on winglet, or a high-downforce, 2-element add-on winglet for maximum steering feel. The tall wing endplates enhance straight-line stability and side-bite in long sweepers. Inspired by popular American open-wheel cars from the late 90s, we also incorporated additional ground clearance at the outer extremities, especially important on U.S. style high-grip carpet. A wide, flat section in the middle of the wing provides a perfect mating surface for any F1 body.

The wings are made from sleek, matte-finished, ultra-durable nylon and will fit most popular F1 cars on the market such as Xray, AE, Tamiya and Roche. They are available in Black color now, with a white option coming soon.

1/10 Adapter for Diff Check - DFC-10

XRAY T4'19 SLP SHOCK TOWER REAR 3.0MM GRAPHITE - 303083

XRAY T4'19 SLP SHOCK TOWER FRONT 3.0MM GRAPHITE - 302082

Rear body mount set with 6mm-thick +1mm height-adjustable body posts. Made from special composite material that provides maximum strength but sufficient flex to reduce body post breakage in hard crashes or car rollovers. The body supports are rounded to have a better fit and provide better support to the car body.

Designed for use with graphite inserts that allow adjustment of the rear posts to three different positions, this body mount set is part of the BPA system – Body Position Adjustment.

For serious racers who focus on the small details, body height plays a very important role in the performance of the car and as such, ultra-fine body height tuning was developed by XRAY R&D engineers to address this increasingly important tuning set-up feature.

The body holders have elevated mounting to make body height adjustment very quick and easy. In a few short seconds and two clicks, you can exchange all the body holders to adjust body height.

There are two optional body height adjustable mounts available: either +1mm or +2mm.

Rear body mount set with 6mm-thick +1mm height-adjustable body posts. Made from special composite material that provides maximum strength but sufficient flex to reduce body post breakage in hard crashes or car rollovers. The body supports are rounded to have a better fit and provide better support to the car body.

Designed for use with graphite inserts that allow adjustment of the rear posts to three different positions, this body mount set is part of the BPA system – Body Position Adjustment.

For serious racers who focus on the small details, body height plays a very important role in the performance of the car and as such, ultra-fine body height tuning was developed by XRAY R&D engineers to address this increasingly important tuning set-up feature.

The body holders have elevated mounting to make body height adjustment very quick and easy. In a few short seconds and two clicks, you can exchange all the body holders to adjust body height.

There are two optional body height adjustable mounts available: either +1mm or +2mm.

Front eccentric body mount set with 6mm-thick +2mm height-adjustable body posts. Made from special composite material that provides maximum strength but sufficient flex to reduce body post breakage in hard crashes or car rollovers. The body supports are rounded to have a better fit and provide better support to the car body. Part of the BPA system – Body Position Adjustment – the eccentric design allows the body posts to be mounted in three different positions to adjust body position. For serious racers who focus on the small details, body height plays a very important role in the performance of the car and as such, ultra-fine body height tuning was developed by XRAY R&D engineers to address this increasingly important tuning set-up feature. The body holders have elevated mounting to make body height adjustment very quick and easy. In a few short seconds and two clicks, you can exchange all the body holders to adjust body height. There are two optional body height adjustable mounts available: either +1mm or +2mm.

Front eccentric body mount set with 6mm-thick +1mm height-adjustable body posts. Made from special composite material that provides maximum strength but sufficient flex to reduce body post breakage in hard crashes or car rollovers. The body supports are rounded to have a better fit and provide better support to the car body.

Part of the BPA system – Body Position Adjustment – the eccentric design allows the body posts to be mounted in three different positions to adjust body position.

For serious racers who focus on the small details, body height plays a very important role in the performance of the car and as such, ultra-fine body height tuning was developed by XRAY R&D engineers to address this increasingly important tuning set-up feature.

The body holders have elevated mounting to make body height adjustment very quick and easy. In a few short seconds and two clicks, you can exchange all the body holders to adjust body height.

There are two optional body height adjustable mounts available: either +1mm or +2mm.

CNC-machined front upper bumper holder made from premium-grade graphite material. Direct replacement for the standard composite bumper upper holder. Accommodates the BPA system – Body Position Adjustment – which uses eccentric body mounts in three different positions to adjust the position of the body.

301151 T4'19 Alu Extra Flex Chassis 2.0mm - Worlds Edition

• World Champion chassis

• Special cutout openings

• Increased flex

• Easier to drive

• For low-to-medium traction tracks

• Fits front chassis brace

• 2mm thickness

• Swiss 7075 T6 aluminum

• Black anodized

Aluminum T4’19 chassis with special cutout openings for increased flex. This chassis is recommended for low-to-medium traction tracks as it generates more traction. (Not recommended for high- and very-high traction conditions where either the #301149 or #301150 chassis work better).

The front brace – which can be easily installed on the chassis with two screws – eliminates side flex at the front of the chassis, improving steering response and making the car more predictable.

Successfully raced by the factory team, and used by Bruno Coelho to win the World Champion title, this is a “must have” for every serious racer.

T4’19 Alu Chassis

301149 T4'19 Alu Chassis 2.0mm - Swiss 7075 T6

• More predictable handling

• Fits front chassis brace

• For very-high traction tracks

• 2mm thickness

• Swiss 7075 T6 aluminum

• Black anodized

Redesigned aluminum chassis to accommodate the new front chassis brace. The front brace – which can be easily installed on the chassis with two screws – eliminates side flex at the front of the chassis, improving steering response and making the car more predictable.

Extensively tested and recommended for high- and very-high traction tracks, this narrow chassis is CNC-machined from 2mm premium Swiss 7075 T6 and additionally black coated.

XRAY ULP ALU SHOCK ADJUSTABLE NUT - V2 - ORANGE (2) - 308044-O

XRAY T4'19 ALU CHASSIS STIFFENER - SWISS 7075 T6 - 306532

XRAY GRAPHITE BATTERY BACKSTOP 2.2MM - 306178

XRAY T4'19 ULP SHOCK TOWER REAR 3.0MM GRAPHITE - 303084

XRAY T4'19 ALU MOTOR MOUNT - ORANGE - 303006-O

XRAY T4'19 ALU LAYSHAFT BULKHEAD RIGHT - ORANGE - 303005-O

XRAY T4'19 ALU LOWER ADJUSTMENT BULKHEAD - FRONT L / REAR R - ORANGE - 302763-O

XRAY T4'19 ALU LOWER ADJUSTMENT BULKHEAD - FRONT R / REAR L - ORANGE - 302762-O

XRAY ALU SHIM FOR RADIAL PLAY ADJUSTMENT OF STEERING ARM - ORANGE (2) - 302544-O

XRAY T4'19 ULP SHOCK TOWER FRONT 3.0MM GRAPHITE - 302083

XRAY T4'19 ALU UPPER CLAMP WITH 2 ADJ. ROLL-CENTERS (L+R) - ORANGE - 302036-O

XRAY GRAPHITE SHIM FOR REAR BODY POST ADJUSTMENT 3.0MM (4) - 301390

Rear body mount set includes 6mm thick body posts made from special composite material that provides maximum strength but sufficient flex to reduce body post breakage in hard crashes or car rollovers. The body supports are rounded to have a better fit and provide better support to the car body. 

XRAY COMPOSITE FRONT ECCENTRIC 6MM BODY MOUNT SET - 301326

XRAY FOAM BUMPER FOR ADJUSTABLE BODY MOUNTS - LIGHT - 301231

XRAY COMPOSITE UPPER HOLDER FOR BUMPER FOR ADJUSTABLE BODY MOUNTS  - 301219

XRAY COMPOSITE BUMPER FOR ADJUSTABLE BODY MOUNTS - 301204

XRAY T4'19 GRAPHITE CHASSIS 2.2MM - 301148

Bittydesign Magnetic Body Post Marker Kit - Color : Orange - BDBPMK10-O

Mon-Tech Racer Pre-Cut Asphalt for Xray - 018-010

Mon-Tech Racer Pre-Cut Carpet for Xray - 018-011